Conferences

I2MTC - 12 May 2014 - Uruguay, South America
Simposio de Metrologia, Santiago de Queretaro, Mexico - 6-10 October 2014

Wanted: Metrology Professional (Chemical emphasis) – Norco, CA

Metrology Professional (Chemical emphasis)
American Technical Services, Inc. (ATS)
Norco, California

Description

American Technical Services, Inc., is a diversified professional services firm providing government and commercial clients a wide range of engineering and IT services. We are currently seeking a Metrology professional to assist us with managing metrology related tasks for the US Navy. This is an excellent opportunity for someone with chemical engineering experience. This position requires a sound understanding of analytical lab equipment including FTIR, and GCMS. Tasks will include performing chemical equipment characterizations and other testing for calibration requirements as well as acquisition logistics support for complex lab equipment. Proficiency in good laboratory practices to include: health, safety and facility requirements for labs. Lab audit experience is a plus. A successful candidate must be able to work in the laboratory unsupervised.

Continue reading Wanted: Metrology Professional (Chemical emphasis) – Norco, CA

Share

Wanted: FT Repair Technician – Dulles, VA & Silicon Valley, CA

FT Repair Technician
SIMCO Electronics
Dulles, VA and Silicon Valley, CA

Company

SIMCO Electronics is the largest independent provider of global calibration, repair, and software solutions, supporting customers worldwide. With corporate headquarters located in the heart of Silicon Valley (near San Francisco, California, USA) our worldwide network of laboratories and international field service teams provide localized support to our customers.

Position Overview

The Repair Technician will apply knowledge of measurement science, mathematics, physics and electronics to perform calibration and repair of test measurement and diagnostic equipment used in the Life Science, RF/Telecommunications, and Semiconductor/Electronic Components markets. This position will normally receive general instructions on work assignments that are semi-routine in nature and where the ability to recognize and apply technical deviations from general troubleshooting and repair is required. The Repair Technician will identify and utilize appropriate manual and automated measurement procedures. The Repair Technician will perform laboratory and work area housekeeping.

Continue reading Wanted: FT Repair Technician – Dulles, VA & Silicon Valley, CA

Share

Now Hiring: Calibration Technicians – Multiple Locations

Calibration Technicians (All levels) – Full time and On-call positions available
SIMCO Electronics
Silicon Valley CA, Seattle WA, Austin TX, Warsaw IN, Allentown PA, Newport News VA, and Dulles VA!

Company

SIMCO Electronics is the largest independent provider of global calibration, repair, and software solutions, supporting customers worldwide. With corporate headquarters located in the heart of Silicon Valley (near San Francisco, California, USA) our worldwide network of laboratories and international field service teams provide localized support to our customers.

Position Overview

The Calibration Technician will apply knowledge of measurement science, mathematics, physics, and electronics to calibrate inspection, measurement, and test equipment in the Acoustical, Chemical, Dimensional, DC/Low Frequency, RF/Microwave, Fluid, Mechanical, Optical, Thermodynamics, and Time & Frequency disciplines to ensure measurement accuracy. The Calibration Technician will identify and utilize appropriate manual and automated measurement procedures.

Continue reading Now Hiring: Calibration Technicians – Multiple Locations

Share

Career Opportunities – Electronic Repair & Calibration Technicians

Electronic Repair Technician &
Electronic Calibration Technician
AcuCal Calibration Services
Manassas, VA

AcuCal is currently seeking calibration and repair technicians in support of our extensive nationwide calibration services.  Ideal candidates will have a background in one or more of the following areas:

Metrology
PMEL
Electronics
Electrical Engineering
ITT

Calibration Technician:  Travel to customer sites (approximately 45%) will be required; locally and out of town.  Ideal experience includes calibrating Meters, Oscilloscopes, RF, Spectrum Analyzers, Signal Generators, Mechanical and Dimensional.

Repair Technician:  Complete repairs on TMDE in house only at VA laboratory. Perform component level troubleshooting, alignment and repair.  Familiarity with testing and repairing this equipment is a requirement: Agilent, Aeroflex, Fluke, IFR/Marconi, Rhode & Schwartz and Anritsu.

 

Continue reading Career Opportunities – Electronic Repair & Calibration Technicians

Share

Position Available: Engineer IV – Las Cruces, NM

Engineer IV
Jacobs Technology Inc.
Las Cruces, NM

This is a NASA Test and Evaluation contract position; it may be assigned to Jacobs Technology Inc. or a teammate company.

Responsibilities:

Independently performs a project assignment that involves complex features and can be guided by codes, standards, and other precedents of the discipline. Analyzes and/or evaluates the results of an analysis using techniques prescribed by senior engineers or supervisors. Accomplishes complete tasks of limited scope or solves problems which require investigation of a limited number of variables. Develops automated procedures using Met/Cal or Lab/View, including integrating measurement uncertainty where beneficial to the customer. Develop written procedures when automation is not beneficial or available. Manages Met/Track calibration system. Oversees electrical calibration group. Proactively interfaces with customers having unique measurement needs. Must be a U.S. Citizen. Must possess a valid state driver’s license. Must pass a Federal background investigation. Must pass an employment physical and submit to drug testing.

Continue reading Position Available: Engineer IV – Las Cruces, NM

Share

Wanted: Metrologist/Quality Engineer – Yorba Linda, CA

Rapidly growing Yorba Linda (California) based instrumentation company is seeking pressure calibration Metrologist/Quality Engineer who is comfortable in a fast pace working environment.

Job Description

Apply measurement science, mathematics, and physics to develop, documentation, and maintain calibration systems, procedures, and methods for pressure calibration and test equipment based on analysis of measurement problems, accuracy and precision requirements. Provide immediate calibration service and customer support. Maintain calibration laboratory, prepare the documentation, and be responsible for application of NVLAP 17025 accreditation. Maintain and improve quality control system. This position comes with full benefits (401K match, paid holidays, vacation, and company bonus).

Continue reading Wanted: Metrologist/Quality Engineer – Yorba Linda, CA

Share